seting deck posts against house

How to Set Square Deck Posts | Hunker

Pull the string along one edge of the planned deck, and use the mark on the string to know where to make a mark on the ground that is 6 feet from the stake. If your deck will be up against your home, measure from a corner against the house to a point 6 feet away that is along the edge of the house.

Get Price

What should I do about deck footings near the house? - Home

To install deck piers properly, the piers must bear on undisturbed soil and, depending on the region, be set below the frost line. This could mean the need for 3-ft.-deep footings in some areas. However, if the piers are in a backfill region, as is the case with piers nearest the house on a freestanding deck, the footing depth may have to be as deep as 10 ft. to reach undisturbed soil and to comply with code.

Get Price

The Buried Post Footing | Decks.com by Seven Trust

The Buried Post Footing. This footing method involves pouring a concrete pad at least 12” thick at the base of your hole. Next, set a pressure treated wood support post rated for "ground contact" on top of the pad and backfill the soil into the hole. "Ground rated" treated wood contains a higher concentration of preservative chemicals than normal wood and will offer increased protection from decay while buried in soil.

Get Price

Setting Fence Posts - Dos and Don'ts - Bob Vila

Typically, in part to ensure that posts lodge below the frost line, experts call for a hole deep enough to submerge the bottom third of the post below ground. For a six-foot-tall post, therefore,

Get Price

How to Easily Install a Fence Post Near or Next to Your House

Start with the post that’s right up beside your house and measure out along the twine so the posts are straight and evenly spaced. Use a post hole digger tool: Use a post hole digger to ensure perfectly sized holes for your fence post. Using a hole digger tool is ideal because if you dig with a normal shovel you’ll end up with a hole that

Get Price

How to Build a Solid, Frost-Proof Deck Footing (DIY) | Family

When you pour concrete footings, hold the cardboard concrete form tube about 12 in. up from the bottom of the footing. Do this by nailing the sides of the tube to the center of a tic-tac-toe grid of 2x4s at the top of the hole. Then dump concrete through the tube into the bottom of the hole.

Get Price

Installing a fence post next to the house - Fine Homebuilding

Dig a post hole to the proper depth as close as you can. Cut a post for this hole that will be even with grade. Let's call this the "short" post. Dig another hole next to the house at least 12" deep. This hole will be for the "long" post" Securely attach the short post to the long post and set the assembly in the holes

Get Price

How close to the house can I put posts for a deck

I'm going to cantilever the joists for the deck, so I don't need the posts to be right up against the house foundation, but I'm still wondering if there's any issues with posts let's say within a foot of the foundation. For the posts I will dig down 4 feet, install a concrete footing and then set a sonotube on top of the footing.

Get Price

Attaching Deck to House Foundation in 2020? - NEW Methods

Attaching a Deck to Brick House Foundation. Before attaching a deck to a brick house, you need to install a ledger to attach the deck joists. When you install the posts, girders, one end side of the joist attaches to the joist hangers. The outer sides will attach to the top of the girders and form a deck’s frame.

Get Price

How to attach a wood rail post to side of the house?

I just want to put up two 6x6 posts with Titan Wood Post Anchors, either 35 or 70 apart, Read More. Total height of low level ground level deck. Apr 28, 20 11:17 AM. I am building a 10'x12'deck (not attached to a ledger board). My plan was to pour concrete footings, then run doubled up 2x8 beams setting on the footings. Read More

Get Price

How to Install Deck Railing Posts | Better Homes & Gardens

Posts are as long as the height of the railing, plus the width of the joist and the thickness of the decking, minus the thickness of the rail cap. Set up a jig that allows you to cut all the posts to the correct length. A 22-1/2-degree angle cut on the bottom adds a decorative touch.

Get Price

How to Build a Deck That'll Last as Long as Your House (DIY

Photo 10: Nail the deck beams. Set the double 2×12 deck beam on the posts and fasten it to the long 2×6 with 16d galvanized box nails. Nail the 2x12s to each other with three nails every 12 in., one close to each edge and one in the middle. Be sure the deck beam projects several inches past the edge of the deck for later trimming.

Get Price

Attaching a New Deck to a House: The Correct Method (DIY)

Select lag screws specifically rated for treated wood, in lengths that will penetrate the ledger, exterior sheathing and the 1-1/2 in. thickness of the house rim joist (4 in. is usually the right length). Use only treated wood intended for soil contact for all the structural members of the deck, including the ledger, joists, beams and posts.

Get Price

Installing a fence post next to the house - Fine Homebuilding

i'm planning on installing a vinyl fence from the side of my house out to an existing vinyl fence running perpandicular. I'm not sure of the best way to secure the post next to my house. i dont want to fasten the post directly to the house. The problem is that i have a fieldstone foundation and when I dig the post hole, i cant get the post close enough to the house because of how uneven the

Get Price

Build a Deck Without Digging Holes Using a Deck Post Base and

Continue to drive it for 30 seconds after the plate has met the ground in order to compact the soil. Place the post in the bracket, secure it with screws, and then build the deck. The first and most noticeable advantage of using post anchors rather than deck blocks is that the post is fixed firmly in place without needing additional cross pieces.

Get Price

Deck Railing Post Anchor. Install Posts to Deck Without

The rise in popularity of deck railing post anchors is no surprise. Anyone who has experienced the ease and speed of installation, eliminating notching of decking and tricky carpentry skills, or all the hardware required for setting posts into joists knows this intimately.

Get Price

Laying Out the Deck | Better Homes & Gardens

Mark the house wall for the positions of the posts. First mark the outside of the framing (the decking will overhang it by 1-1/2 inches). Then measure over and mark where the post will be located. Make sure you identify the center of the post. Then drive a batterboard into the ground near the house, more or less centered over the post location.

Get Price

How To Builid Code-Compliant Deck Railings & Posts

With posts on the inside of deck joists joist, you can use two corner posts, as shown in the detail above. With two corner posts, the top rails extend beyond the posts and meet at the corner. Another option is to use a single post at the corner, installed the same way as the inside posts in Detail A, above.

Get Price

Building a Code-Compliant Deck - Extreme How To

NOTE – The latest building codes require decks supported by a house to be built with a “positive attachment” to resist lateral loads. This is accomplished using hardware connectors that tie the deck into the house to protect against lateral stresses from wind, seismic or people on the deck.

Get Price

Flashing A Deck Ledger Board Properly - How To

I asked a local lumber supplier about it. He knew exactly what I was talking about but only had two options. One, fasten the ledger to the brick (which is against code), or two, put posts/beam near the house and don’t connect to the house. The problem with putting them near the house is the post footings need to go 8ft deep.

Get Price

fence - Placing fencepost close to house? - Home Improvement

If your last post was 2' away, it would be easy enough to make a bit of fence structure that leans against your house. That said, however, I respectfully disagree with the "don't put a hole in your siding" argument. First, I can't imagine how you'd see differential movement between the post/house and tearing of the siding.

Get Price

How to Install Posts in the Water for a Dock or Pier: 14 Steps

For standard 8 ft (2.4 m) decks, a PVC pipe with a diameter of 12 in (30 cm) and a post with a diameter of 4 in (10 cm) should be sufficient. If you’re building a deck that is larger than 8 ft (2.4 m), start with a PVC pipe of 18 in (46 cm) and a post that’s about 6 in (15 cm).

Get Price

Jack Posts - Building Hardware - The Seven Trust

The Tiger Brand Jack Post Super "S" 3 ft. Jack Post can adjust from a 1 ft. 7 in. to 3 ft. It has a compression load range of 18,000 lbs. at its lowest setting and 16,000 lbs. at its highest setting. It is ideal for correcting sagging floors and basement beams and providing secondary support for room additions, remodeling projects, porches and

Get Price

How to Install Deck Railing Posts | Better Homes & Gardens

Posts are as long as the height of the railing, plus the width of the joist and the thickness of the decking, minus the thickness of the rail cap. Set up a jig that allows you to cut all the posts to the correct length. A 22-1/2-degree angle cut on the bottom adds a decorative touch.

Get Price

How To Builid Code-Compliant Deck Railings & Posts

With posts on the inside of deck joists joist, you can use two corner posts, as shown in the detail above. With two corner posts, the top rails extend beyond the posts and meet at the corner. Another option is to use a single post at the corner, installed the same way as the inside posts in Detail A, above.

Get Price

How Install Concrete Deck Footings - Homedit

How Install Concrete Deck Footings. This is a tutorial that shows a step-by-step method for installing concrete deck footings, specifically for a low deck or wood patio.. There are a variety of ways to do this, of course, but this is a very fast and relatively simple way that we’ve used for multiple projects with excellent res

Get Price

How to set and align fence posts

One-man method. The ‘stake-out’ method makes it possible for a man working alone to align a fence. Drive two stakes into firm ground near each post, and nail an arm to each stake. Set posts onto rock or gravel at the bottom of the hole, checking alignment against the string. Use a level or a plumb bob to true one face of the post.

Get Price

How to Select Your Ideal Deck Railing Color

Tranquil White looks especially striking in coastal settings or against a home with crisp, white trim. If you’re adding railing to a front porch, this classic white is a can’t-miss choice. Serene Black provides the perfect balance of traditional styling (check out the sculpted top rail) and contemporary flair.

Get Price

Sealing a Deck? Follow 8 These Dos and Don'ts - Bob Vila

A backyard deck is the perfect platform for good times, but that wooden surface needs a proper sealant to protect it against the ravages of sun, rain, and temperature fluctuations.

Get Price

DIY Build a Freestanding Cantilevered Deck - Extreme How To

The higher the deck is from the ground, the longer its support posts will need to be and the more likely the deck will be unstable. Thanks to an uphill slope at the rear of the house, the deck surface was only 5 feet high next to the house but closer to 3-1/2 feet on the far end.

Get Price

Attaching a Deck Ledger to a Stucco Wall - GreenBuildingAdvisor

After reading another current post on deck to ledger connections, we have a related question. In 2016, we built a 2 car garage with a small efficiency apartment above it. The wall construction of the garage/apartment is; 1) Zip System sheathing, 2) Benjamin Obdyke 6 mm Slicker Max rain screen, 3) stucco lathe, 4) stucco. We are now getting ready to start building a house in Asheville, NC which

Get Price

How to Select Your Ideal Deck Railing Color

Tranquil White looks especially striking in coastal settings or against a home with crisp, white trim. If you’re adding railing to a front porch, this classic white is a can’t-miss choice. Serene Black provides the perfect balance of traditional styling (check out the sculpted top rail) and contemporary flair.

Get Price

Replacing Support Posts | A Masters Hands

Set the bottom end of the post in place, so that the anchor bolts fit through the holes in the box bracket, while leaning the top end of the post off at an angle (usually inside, under the deck, to clear outside overhanging trim pieces), and then swing the top of the post up and into position.

Get Price

How to set and align fence posts

One-man method. The ‘stake-out’ method makes it possible for a man working alone to align a fence. Drive two stakes into firm ground near each post, and nail an arm to each stake. Set posts onto rock or gravel at the bottom of the hole, checking alignment against the string. Use a level or a plumb bob to true one face of the post.

Get Price

Freestanding Deck Building Instructions | DoItYourself.com

The most expeditious and economical way to support the deck is with individual concrete footings. The deck frame will include vertical supports or posts (4x4 or 6x6); each post bears on a separate concrete footing. The footings are poured into 12-inch diameter cylindrical cardboard forms set in holes dug deep enough to penetrate the frost line.

Get Price

8 Ground Level (Floating) Deck Footings - Plasticine House

With deck anchors, your deck can be built as low as 2” from the underside of the beams to surface grade or as high as 6’ from the top of the deck to grade. If your deck is higher than 18”, you will need to brace the posts to the beams and joists. Price. Sold on deck foot anchors? Not so fast. You’ll pay for all that convenience.

Get Price

How to Mount a Deck Frame to Concrete Foundation

View in gallery. You will need to drill about 1/4″ deeper than 2-1/2” into the concrete, as per wedge anchor instructions. Because it is more accurate to place the 2×6 and drill through that into the concrete (better to align them precisely when they’re drilled together), we measured and marked with colorful tape on the drill bit 4-1/2”, which gives us a little extra space just in case.

Get Price

Terminology of decks - WOOD Magazine

Posts: Timbers (usually 4x or 6x) set vertically to support the deck framing. Posts are used on all but the shortest decks. The posts can be cut off below the deck surface, or they may rise above the surface to provide support for the railing. Posts may rest on top of concrete footings or they can be set plumb in the hole before the concrete is

Get Price

Fill That Post Hole With Concrete | Porters Building Centers

Fill That Post Hole With Concrete! When you’re building a deck, a fence, a pole building or whatever, everyone thinks that the hole MUST be filled with concrete. I did a little research and on this subject and surprisingly there are a couple websites where this question has been asked with varying answers.

Get Price

Product Details

Product List